Accelerometer Configuration - Revision history

Editor: /* Step 2: Enable or Disable Accelerometer */

2025-08-28T17:05:56Z

Step 2: Enable or Disable Accelerometer

← Older revision		Revision as of 17:05, 28 August 2025
Line 77:		Line 77:
	'''Meaning:'''		'''Meaning:'''

	* 0 → ~~Enable~~		* 0 → Disable

	* 1 → ~~Disable~~		* 1 → Enable

	'''Example:'''		'''Example:'''
Line 116:		Line 116:
	Error : 0		Error : 0
	</pre>		</pre>

	=== Step 3: Save Configuration ===		=== Step 3: Save Configuration ===

Editor: /* Step 1: Set Device Orientation */

2025-08-06T04:23:00Z

Step 1: Set Device Orientation

← Older revision		Revision as of 04:23, 6 August 2025
Line 20:		Line 20:

	=== Step 1: Set Device Orientation ===		=== Step 1: Set Device Orientation ===
			SET CUORIENTATION:<orientation number> <br>
			Orientation Number:<br>
			1 = GPS antenna facing sky, wire pointing towards passenger <br>
			2 = GPS antenna facing passenger, wire pointing down<br>
			3 = GPS antenna facing sky, wire pointing to right side<br>
			4 = GPS antenna facing passenger, wire pointing to right side<br>

	'''Command Format:'''		'''Command Format:'''
	<pre>		<pre>

	SET CUORIENTATION:<orientation number>		SET CUORIENTATION:<orientation number>
	</pre>		</pre>
Line 32:		Line 37:
	SET CUORIENTATION:1		SET CUORIENTATION:1
	</pre>		</pre>

	'''Expected Response:'''		'''Expected Response:'''
	<pre>		<pre>
Line 62:		Line 66:
	Error : 0		Error : 0
	</pre>		</pre>

	=== Step 2: Enable or Disable Accelerometer ===		=== Step 2: Enable or Disable Accelerometer ===

Editor: /* Step 3: Save Configuration */

2025-08-06T04:17:40Z

Step 3: Save Configuration

← Older revision		Revision as of 04:17, 6 August 2025
Line 117:		Line 117:
	After all the above commands, use the mandatory save command:		After all the above commands, use the mandatory save command:
	<pre>		<pre>
			SET CUMR:2
			</pre>

	~~SET TSMR:2~~
	~~</pre>~~

	=== Step 4: Verify Data on Server ===		=== Step 4: Verify Data on Server ===

Editor at 05:14, 27 June 2025

2025-06-27T05:14:26Z

← Older revision		Revision as of 05:14, 27 June 2025
Line 1:		Line 1:
	== ~~Accelerometer~~ Configuration Guide ==		==Configuration Guide==

	=== 📘 What is an Accelerometer? ===		=== 📘 What is an Accelerometer? ===

Editor: Created page with "== Accelerometer Configuration Guide == === 📘 What is an Accelerometer? === An accelerometer is an internal sensor that detects motion, vibration & tilt. It measures acceleration forces and is used to detect: * Harsh acceleration * Harsh braking * Harsh cornering === ⚙️ Purpose of Accelerometer Configuration === Enabling and configuring the accelerometer allows the device to: * Generate event-based alerts (e.g., harsh braking, harsh turns) To configure..."

2025-06-27T05:13:55Z

Created page with "== Accelerometer Configuration Guide == === 📘 What is an Accelerometer? === An accelerometer is an internal sensor that detects motion, vibration & tilt. It measures acceleration forces and is used to detect: * Harsh acceleration * Harsh braking * Harsh cornering === ⚙️ Purpose of Accelerometer Configuration === Enabling and configuring the accelerometer allows the device to: * Generate event-based alerts (e.g., harsh braking, harsh turns) To configure..."

New page

== Accelerometer Configuration Guide ==

=== 📘 What is an Accelerometer? ===

An accelerometer is an internal sensor that detects motion, vibration & tilt. It measures acceleration forces and is used to detect:

* Harsh acceleration

* Harsh braking

* Harsh cornering

=== ⚙️ Purpose of Accelerometer Configuration ===

Enabling and configuring the accelerometer allows the device to:

* Generate event-based alerts (e.g., harsh braking, harsh turns)

To configure the accelerometer correctly, the device must be placed on a flat surface (level = 0°). There are 4 supported orientations in Transight devices. You must declare the orientation during setup.

=== Step 1: Set Device Orientation ===

'''Command Format:'''
<pre>

SET CUORIENTATION:<orientation number>
</pre>

'''Example:'''
<pre>

SET CUORIENTATION:1
</pre>

'''Expected Response:'''
<pre>

IMEI: 862942074896044

Command: SET CUORIENTATION:1

Response: ACCELERO_ORIENTATION: 1

Error : 0
</pre>

'''Verification Command:'''
<pre>

GET CUORIENTATION
</pre>

'''Expected Response:'''
<pre>

IMEI: 862942074896044

Command: GET CUORIENTATION

Response: ACCELERO_ORIENTATION: 1

Error : 0
</pre>

=== Step 2: Enable or Disable Accelerometer ===

'''Command Format:'''
<pre>

SET CUACCELENABLE:<0/1>
</pre>

'''Meaning:'''

* 0 → Enable

* 1 → Disable

'''Example:'''
<pre>

SET CUACCELENABLE:1
</pre>

'''Expected Response:'''
<pre>

IMEI: 862942074896044

Command: SET CUACCELENABLE:1

Response: ACCELERO_ENABLE_STATUS: 1

Error : 0
</pre>

'''Verification Command:'''
<pre>

GET CUACCELENABLE
</pre>

'''Expected Response:'''
<pre>

IMEI: 862942074896044

Command: GET CUACCELENABLE

Response: ACCELERO_ENABLE_STATUS: 1

Error : 0
</pre>

=== Step 3: Save Configuration ===

After all the above commands, use the mandatory save command:
<pre>

SET TSMR:2
</pre>

=== Step 4: Verify Data on Server ===

* Check the packets sent by the device to the server.

* Ensure all accelerometer-related alerts (e.g., harsh braking, harsh turning) are being received correctly.