Editor: /* Save Configuration */

2025-08-06T04:29:22Z

Save Configuration

← Older revision		Revision as of 04:29, 6 August 2025
Line 95:		Line 95:
	After setting up geofences, you must execute the below command to save the configuration permanently:		After setting up geofences, you must execute the below command to save the configuration permanently:
	<pre>		<pre>
	SET ~~TSMR~~:2		SET CUMR:2
	</pre>		</pre>

Editor at 06:28, 28 June 2025

2025-06-28T06:28:02Z

← Older revision	Revision as of 06:28, 28 June 2025
Line 1:	Line 1:
		== Introduction ==
		Geofencing is a core feature in modern GPS tracking systems. It allows users to define virtual boundaries on a map. When a GPS-tracked vehicle or asset enters or exits these areas, the system automatically triggers alerts or actions.
		== How Geofence Works ==
		* A geofence can be a circular or polygonal area defined by latitude and longitude.
		* The Discovery 4G GPS tracker continuously checks its current location via satellite.
		* The system compares this live data against the predefined geofence area.
		* If the asset enters or exits, the event is logged or notified based on configuration.

		== How to Get Coordinates from Google Maps ==
		# Open [https://maps.google.com Google Maps]
		# Search for your desired location (e.g., warehouse, school)
		# Right-click on the location and select '''“What’s here?”'''
		# Note the coordinates shown below (e.g., '''10.0556255, 76.3544891''')
		# Use these as:
		## Center point for circular geofences
		## Corner points for polygon geofences (at least 3, ideally 4–6)
		# Enter the values into the command format explained below

		'''Note''': A maximum of '''6 geofences''' (circle or polygon combined) can be configured on any Transight telematics device.

		== Geofence Command Format ==
		* '''Status''': 1 = Enable, 0 = Disable
		* '''Geofence ID''': Unique ID (e.g., 1313, 1777)
		* '''Alert Type''': 1 = Entry, 2 = Exit, 3 = Both
		* '''Shape''': 0 = Circle, 1 = Polygon
		* '''Latitude/Longitude''': Decimal format (e.g., 10.0556255, 76.3544891)
		* '''Radius''': Only for circles (in meters)
		* '''#''': Used to separate parameters
		* '''&''': Must be added at the end of polygon commands

		== Command Examples with Field Mapping ==

		=== Example 1: Circular Geofence ===
		'''Objective''': Create a 1000-meter circular geofence at '''10.0556255, 76.3544891'''

		* Status: 1
		* Geofence ID: 1313
		* Alert Type: 3
		* Shape: 0
		* Latitude: 10.0556255
		* Longitude: 76.3544891
		* Radius: 1000

		'''Command format:'''
		<pre>
		SET CUGF:<Status><Geofence ID>-<Alert Type>-<Shape>#<Latitude-Longitude>#<Radius>
		</pre>

		'''Example:'''
		<pre>
		SET CUGF:1-1313-3-0#10.0556255-76.3544891#1000
		</pre>

		'''Response:'''
		<pre>
		IMEI: 862942074896044
		Command: SET CUGF:1-1313-3-0#10.0556255-76.3544891#1000
		Response:
		Error : 0
		</pre>

		=== Example 2: Polygon Geofence ===
		'''Objective''': Create a polygon geofence with 4 corner points (first point repeated at the end)

		* Status: 1
		* Geofence ID: 1777
		* Alert Type: 3
		* Shape: 1
		* Coordinates:
		** 10.0535097, 76.334262
		** 10.0504267, 76.3328855
		** 10.0474386, 76.3439598
		** 10.0503084, 76.3437023
		** 10.0535097, 76.334262 (repeat to close loop)

		'''Command format:'''
		<pre>
		SET CUGF:<Status><Geofence ID>-<Alert Type>-<Shape>#<Lat-Long>#...#<Lat-Long>&
		</pre>

		'''Example:'''
		<pre>
		SET CUGF:1-1777-3-1#10.0535097-76.334262#10.0504267-76.3328855#10.0474386-76.3439598#10.0503084-76.3437023#10.0535097-76.334262&
		</pre>

		'''Response:'''
		<pre>
		IMEI: 862942074896044
		Command: SET CUGF:1-1777-3-1#...
		Response:
		Error : 0
		</pre>

		== Save Configuration ==
		After setting up geofences, you must execute the below command to save the configuration permanently:
		<pre>
		SET TSMR:2
		</pre>

		== To Check Configured Geofences ==
		Use the command:
		<pre>
		GET CUGF
		</pre>
		This will show all geofences currently saved in the device memory.

		==Final Verification ==
		After setup:
		* Ensure the device has a GPS fix
		* Drive or move the asset in and out of the geofenced area
		* Confirm alerts are received/logged as expected

Editor: Created blank page

2025-06-28T05:20:45Z

Created blank page

New page

Geofence Configuration - Revision history

Editor: /* Save Configuration */

Editor at 06:28, 28 June 2025

Editor: Created blank page