Installation Instruction - Revision history

Editor: /* 3. Device Mounting Guidelines */

2025-12-08T07:28:34Z

3. Device Mounting Guidelines

@@ Line 63: / Line 63: @@
 </div>
 === 4. Wiring Instructions ===
 '''Before Wiring'''<br>

Editor at 07:26, 8 December 2025

2025-12-08T07:26:38Z

@@ Line 37: / Line 37: @@
 Important Rule:<br>
   ➡ Device top surface must face the sky for proper GPS reception.
-&#9989; '''Recommended Locations''' <br>
+<div style="border:2px solid #1a7f00; padding:10px; background:#e9ffe9;">
-*Inside dashboard near windshield
+<b>&#9989; Recommended Locations</b><br><br>
-*Under plastic trims near A-pillar
+<ul>
-*Under dashboard with sky visibility
+<li>Inside dashboard near windshield</li>
 &#10060;'''Avoid Locations'''<br>

Editor at 07:19, 8 December 2025

2025-12-08T07:19:26Z

← Older revision		Revision as of 07:19, 8 December 2025
Line 71:		Line 71:
	\| <div style="color: Green; font-weight: bold;"> GREEN</div>\|\| 2 \|\| Vehicle ignition line (12V) \|\| Detects ignition state \|\| Confirm 12V only when key is ON and 0V when OFF using a multimeter.		\| <div style="color: Green; font-weight: bold;"> GREEN</div>\|\| 2 \|\| Vehicle ignition line (12V) \|\| Detects ignition state \|\| Confirm 12V only when key is ON and 0V when OFF using a multimeter.
	\|}		\|}
	<~~pre~~> ⚠️ Critical Ignition Warning </~~pre~~>		<div style="border:2px solid #cc0000; padding:10px; background:#fff4f4;">
	If the GREEN ignition wire is wrongly connected:		<b>⚠️ Critical Ignition Warning</b><br><br>
	*Device may remain in sleep mode		If the <span style="color:green; font-weight:bold;">GREEN ignition wire</span> is wrongly connected:
	*Old/stale location may appear		<ul>
	*Speed & movement detection may fail		<li>Device may remain in sleep mode</li>
	<~~pre~~> ✅Mandatory Multimeter Verification </~~pre~~>		<li>Old / stale location may appear</li>
	Using a multimeter,<br>		<li>Speed & movement detection may fail</li>
	~~confirm:~~		</ul>
	*RED (Power): Continuous voltage even when engine is OFF		</div>
	*GREEN (Ignition): 12V only when key is ON, 0V when OFF		<div style="border:2px solid #1a7f00; padding:10px; background:#f3fff3;">
	*BLACK (Ground): Near-zero resistance and noise-free		<b>✅ Mandatory Multimeter Verification</b><br><br>
	After wiring:		Using a multimeter, confirm:
	*Crimp joints using crimping tool		<ul>
	*Insulate all joints using insulation tape / heat-shrink sleeves		<li><b>RED (Power):</b> Continuous voltage even when engine is OFF</li>
			<li><b>GREEN (Ignition):</b> 12V only when key is ON, 0V when OFF</li>
			<li><b>BLACK (Ground):</b> Near-zero resistance and noise-free</li>
			</ul>
			After wiring:
			<ul>
			<li>Crimp joints using a crimping tool</li>
			<li>Insulate all joints using insulation tape / heat-shrink sleeves</li>
			</ul>
			</div>

	=== 5. LED Status — Normal Operation ===		=== 5. LED Status — Normal Operation ===
	{\| class="wikitable" style="width:100%"		{\| class="wikitable" style="width:100%"

Editor: /* Discovery Device — Installation & Commissioning */

2025-12-08T07:13:47Z

Discovery Device — Installation & Commissioning

← Older revision		Revision as of 07:13, 8 December 2025
Line 13:		Line 13:
	* Fuse tap with blade fuse – Protected battery power		* Fuse tap with blade fuse – Protected battery power
	==== Safety Instructions ====		==== Safety Instructions ====
	⚠️ Before starting any work:		<pre> ⚠️ Before starting any work: </pre>
	* Turn vehicle ignition OFF		* Turn vehicle ignition OFF
	* Disconnect battery if required by OEM practice		* Disconnect battery if required by OEM practice
Line 71:		Line 71:
	\| <div style="color: Green; font-weight: bold;"> GREEN</div>\|\| 2 \|\| Vehicle ignition line (12V) \|\| Detects ignition state \|\| Confirm 12V only when key is ON and 0V when OFF using a multimeter.		\| <div style="color: Green; font-weight: bold;"> GREEN</div>\|\| 2 \|\| Vehicle ignition line (12V) \|\| Detects ignition state \|\| Confirm 12V only when key is ON and 0V when OFF using a multimeter.
	\|}		\|}
	⚠️ Critical Ignition Warning <br>		<pre> ⚠️ Critical Ignition Warning </pre>
	If the GREEN ignition wire is wrongly connected:		If the GREEN ignition wire is wrongly connected:
	*Device may remain in sleep mode		*Device may remain in sleep mode
	*Old/stale location may appear		*Old/stale location may appear
	*Speed & movement detection may fail		*Speed & movement detection may fail
	✅Mandatory Multimeter Verification		<pre> ✅Mandatory Multimeter Verification </pre>
	Using a multimeter, confirm:		Using a multimeter,<br>
			confirm:
	*RED (Power): Continuous voltage even when engine is OFF		*RED (Power): Continuous voltage even when engine is OFF
	*GREEN (Ignition): 12V only when key is ON, 0V when OFF		*GREEN (Ignition): 12V only when key is ON, 0V when OFF
Line 99:		Line 100:
	\|<div style="color: Green; font-weight: bold;"> Network</div> \|\| Green \|\| Blink every ~2 sec \|\| Network registered		\|<div style="color: Green; font-weight: bold;"> Network</div> \|\| Green \|\| Blink every ~2 sec \|\| Network registered
	\|}		\|}
	✅If all LEDs match → Device is working properly		<pre> ✅If all LEDs match → Device is working properly </pre>
	=== 6. LED Status — Troubleshooting Guide ===		=== 6. LED Status — Troubleshooting Guide ===
	{\| class="wikitable" style="width:100%"		{\| class="wikitable" style="width:100%"
Line 124:		Line 125:
	**Speed updates		**Speed updates
	**Ignition ON / OFF events		**Ignition ON / OFF events
	❗ If any point fails → Recheck wiring using multimeter and verify LED status again.		<pre> ❗ If any point fails → Recheck wiring using multimeter and verify LED status again.</pre>

	=== 8. Finalization ===		=== 8. Finalization ===

Editor at 07:01, 8 December 2025

2025-12-08T07:01:42Z

Show changes

Editor: /* Tools & Materials */

2025-12-06T09:51:07Z

Tools & Materials

← Older revision		Revision as of 09:51, 6 December 2025
Line 2:		Line 2:
	=== 1. Pre-Installation Requirements ===		=== 1. Pre-Installation Requirements ===
	==== Tools & Materials ====		==== Tools & Materials ====
	* ~~Telematics device~~ with wiring harness		* Discovery Device with wiring harness
	* Active SIM card (data enabled)		* Active SIM card (data enabled)
	* Wire tap connectors / crimp terminals		* Wire tap connectors / crimp terminals

Editor: /* 4. Wiring Instructions */

2025-12-06T09:49:00Z

4. Wiring Instructions

← Older revision		Revision as of 09:49, 6 December 2025
Line 43:		Line 43:
	!style="background-color:#680022; color:white;" \| Notes		!style="background-color:#680022; color:white;" \| Notes
	\|-		\|-
	\| RED \|\| 1 \|\| Vehicle Battery + (9–90V DC) \|\| Main power \|\| Always powered — ensures continuous tracking even after the engine is off		\| <div style="color: Red; font-weight: bold;"> RED </div>\|\| 1 \|\| Vehicle Battery + (9–90V DC) \|\| Main power \|\| Always powered — ensures continuous tracking even after the engine is off
	\|-		\|-
	\| BLACK \|\| 7 \|\| Vehicle chassis ground \|\| Ground reference \|\| Ensure clean metal contact		\| <div style="color: Black; font-weight: bold;"> BLACK </div>\|\| 7 \|\| Vehicle chassis ground \|\| Ground reference \|\| Ensure clean metal contact
	\|-		\|-
	\| GREEN \|\| 2 \|\| Vehicle ignition line (12V) \|\| Detects ignition state \|\| Must give 12V when key ON and 0V when ignition OFF		\| <div style="color: Green; font-weight: bold;"> GREEN</div>\|\| 2 \|\| Vehicle ignition line (12V) \|\| Detects ignition state \|\| Must give 12V when key ON and 0V when ignition OFF
	\|}		\|}

Editor: /* 8. Finalization */

2025-12-06T09:45:14Z

8. Finalization

← Older revision		Revision as of 09:45, 6 December 2025
Line 99:		Line 99:
	* Refit trims and panels properly		* Refit trims and panels properly
	* Record installation date & vehicle details		* Record installation date & vehicle details
	* Take ~~photos~~ of connections and device placement		* Take Photos of connections and device placement and save it, later it can be used for troubleshooting
	* Take a 10 sec video for LED status		* Take a 10 sec video for LED status and save it , later it can be used for troubleshooting

	=== Quick Troubleshooting Summary ===		=== Quick Troubleshooting Summary ===

Editor: Created page with "== Discovery Device — Installation & Commissioning == === 1. Pre-Installation Requirements === ==== Tools & Materials ==== * Telematics device with wiring harness * Active SIM card (data enabled) * Wire tap connectors / crimp terminals * Multimeter (for voltage checks) * Automotive insulation tape * Cable ties ==== Safety Instructions ==== * Turn vehicle '''OFF''' before wiring * Avoid Airbag, ECU, ABS and CAN bus wiring routes * Ensure wiring does not interfere with..."

2025-12-06T09:36:01Z

Created page with "== Discovery Device — Installation & Commissioning == === 1. Pre-Installation Requirements === ==== Tools & Materials ==== * Telematics device with wiring harness * Active SIM card (data enabled) * Wire tap connectors / crimp terminals * Multimeter (for voltage checks) * Automotive insulation tape * Cable ties ==== Safety Instructions ==== * Turn vehicle '''OFF''' before wiring * Avoid Airbag, ECU, ABS and CAN bus wiring routes * Ensure wiring does not interfere with..."

New page

== Discovery Device — Installation & Commissioning ==
=== 1. Pre-Installation Requirements ===
==== Tools & Materials ====
* Telematics device with wiring harness
* Active SIM card (data enabled)
* Wire tap connectors / crimp terminals
* Multimeter (for voltage checks)
* Automotive insulation tape
* Cable ties

==== Safety Instructions ====
* Turn vehicle '''OFF''' before wiring
* Avoid Airbag, ECU, ABS and CAN bus wiring routes
* Ensure wiring does not interfere with moving/heat sources

=== 2. SIM Installation ===
* Insert SIM card properly into device slot
* Ensure data plan active
* Confirm SIM is properly seated and locked
* Press the Restart button on the PCB

=== 3. Device Mounting Guidelines ===
Device must be placed with its top surface facing the sky.

'''Recommended Zones'''
* Inside dashboard near windshield
* Under plastic trims with sky visibility
* Away from electronics that cause interference

'''Avoid'''
* Engine compartment
* Enclosed metal cavities
* Areas exposed to high temperature or vibration

Secure using cable ties / OEM tape to avoid loose fitting.

=== 4. Wiring Instructions ===
{| class="wikitable" style="width:100%"
!style="background-color:#680022; color:white;" | Wire Color
!style="background-color:#680022; color:white;" | Pin No.
!style="background-color:#680022; color:white;" | Connect To
!style="background-color:#680022; color:white;" | Purpose
!style="background-color:#680022; color:white;" | Notes
|-
| RED || 1 || Vehicle Battery + (9–90V DC) || Main power || Always powered — ensures continuous tracking even after the engine is off
|-
| BLACK || 7 || Vehicle chassis ground || Ground reference || Ensure clean metal contact
|-
| GREEN || 2 || Vehicle ignition line (12V) || Detects ignition state || Must give 12V when key ON and 0V when ignition OFF
|}

:''Important:'' If Ignition (Green) wire not connected correctly → Device stays in sleep mode → sends old location, no movement/speed detection. Always confirm power continuity and ignition behavior before finishing.

=== 5. LED Status — Normal Operation ===
{| class="wikitable" style="width:100%"
!style="background-color:#680022; color:white;" | LED
!style="background-color:#680022; color:white;" | Color
!style="background-color:#680022; color:white;" | Pattern
!style="background-color:#680022; color:white;" | Meaning
|-
|<div style="color: Red; font-weight: bold;"> Power </div>|| Red || Solid || Power OK
|-
|<div style="color: Red; font-weight: bold;"> User </div>|| Red || Blinking || Processor functioning
|-
|<div style="color: Orange; font-weight: bold;"> GNSS </div> || Orange || Blink every ~2 sec || GPS fix OK
|-
|<div style="color: Green; font-weight: bold;"> Network</div> || Green || Blink every ~2 sec || Network registered
|}

=== 6. LED Status — Troubleshooting Guide ===
{| class="wikitable" style="width:100%"
!style="background-color:#680022; color:white;" | LED
!style="background-color:#680022; color:white;" | Behavior
!style="background-color:#680022; color:white;" | Condition
!style="background-color:#680022; color:white;" | Corrective Action
|-
|<div style="color: Red; font-weight: bold;"> Power </div> || OFF || No power || Check VCC & GND wiring
|-
| <div style="color: Red; font-weight: bold;"> User </div> || OFF || Modem not initialized || Reboot device / wiring recheck
|-
| <div style="color: Orange; font-weight: bold;"> GNSS </div> || OFF || No GPS fix || Re-mount device facing sky
|-
|<div style="color: Green; font-weight: bold;"> Network</div> || Fast blinking || Searching for network || Move vehicle to open area, check SIM
|-
| <div style="color: Green; font-weight: bold;"> Network</div>|| Double blinking || SIM not registered || Verify data pack & signal
|}

=== 7. Commissioning & Validation ===
Perform 2 km road test:
* Live movement visible on portal
* Speed & location updates correctly
* Ignition ON/OFF events visible

If any parameter fails → check wiring & LEDs again.

=== 8. Finalization ===
* Secure all wiring with cable ties
* Ensure no loose parts behind dashboard
* Refit trims and panels properly
* Record installation date & vehicle details
* Take photos of connections and device placement
* Take a 10 sec video for LED status

=== Quick Troubleshooting Summary ===
{| class="wikitable" style="width:100%"
!style="background-color:#680022; color:white;" | Issue
!style="background-color:#680022; color:white;" | Likely Cause
!style="background-color:#680022; color:white;" | Fix
|-
| No power || RED wire or GND issue || Re-check wiring points
|-
| Shows old location data || Ignition (Green) wire error || Confirm ignition 12V signal when ignition is ON
|-
| No GPS || Blocked sky view || Change mounting position
|-
| No network || SIM / signal issue || Replace or reinsert SIM
|}