Commands of Discovery 4G

Configuration Commands	Example and Response	Description	Commnad Type (SET/GET)
URL	SET CUURL:TCP:<IP>:<PORT> SET CUURL:url (HTTP) Example: SET CUURL:http://livedata.transight.net:6000/data SET CUURL:TCP:15.235.9.66:50334 GET CUURL Response: URL:http://livedata.customert.net:6000/data URL:TCP:15.235.9.66:50334	To SET and GET server URL for customer and transight IPs in HTTP and TCP protocol. Data packets will send from device to the pointed IP address.	SET GET
UR(in seconds).	SET CUUR:<duration> GET CUUR Example: SET CUUR:30 GET CUUR Response: UR: 30	Update rate in motion, duration is in seconds Packets will be generating in this frequency.	SET, GET
URT(halt,in minute).	SET CUURT:<duration in mins> GET CUURT Example: SET CUURT:30 GET CUURT Response: CUURT: 30	Update rate in halt, duration is in minutes	SET, GET
URS(sleep, in minute).	SET CUURS:<duration> GET CUURS Example: SET CUURS:30 GET CUURS Response: CUURS: 30	Update rate in sleep, duration is in minutes	SET, GET
M1	SET CUM1:<+91xxxxxxxxxx> GET CUM1 Response: M1: +919656691846	This enables the customer to configure the device and setup alert recipients.	SET, GET
M2	SET CUM2:<+91xxxxxxxxxx> GET CUM2 Response: M2: +919656691846	Secondary mobile number for alerts	SET, GET
APN	SET CUAPN:<APN> M2MISAFEcom(For VI) airtelgprs.com(For Airtel) GET CUAPN Response: APN:M2MISAFE	Access Point Name (APN) for internet connectivity	SET, GET
FRNO	SET CUFRNO:<number> GET CUFRNO Example: SET CUFRNO:12 GET CUFRNO Response: FRNO:12	This command is used to get or set the current frame number. The frame numbers are generated in sequential order.	SET GET
FSMODE	SET CUFSMODE:<0/1> GET CUFSMODE Example: SET CUFSMODE:1 GET CUFSMODE Response: FSMODE:1	This command would set the file system mode: 0-FIFO 1-LIFO	SET GET
IOCFG	SET CUIOCFG:<IO Number>-<IO Mode>-<IO Function*>-<IO Number>-<IO Mode>-<IO Function*>-<IO Number><IO Mode>-<IO Function*> Example: SET CUIOCFG:IO1-DI-GEN*IO2-DO-GEN*IO3-AN-GEN* GET CUIOCFG Response CUIOCFG: IO1-DI-GEN*IO2-DO-GEN*IO3-AN-GEN	This command is used to configure the pin as Digital Input, or Digital Output, or Analog. AN - Analog DO - Digital Output DI - Digital Input	SET GET
ENIP	SET CUENIP:<IP>.<state>,<IP>.<state> Example: SET CUENIP:0.1,1.0 GET CUENIP Response: ENIP:0.1,1.0	IP:Transight-0, Customer-1 State: 1- Enabled 0- Disabled ENIP:0.1,1.1	SET GET
DO	SET CUDO:1.n,2.n (n=0:off,1:on) GET CUDO Response: DO 1:OFF/ON-DO 2:OFF/ON	Pin Number: 1 or 2 Pin State: 0-off, 1-On Each pin configuration separated by"",""	SET GET
VID	SET CUVID:TRANSI GET CUVID Response: VID: TRANSI	Set/Get vendor ID	SET GET
DI	GET CUDI Response: DI:000	Get digital input status	GET
AI	GET CUAI Response: AI:0-0-0	Get analog input voltage values	GET
GF	Polygon: SET CUGF:<Status><geofence ID>-<alert type>-<shape>#<latitude-longitude>#....& Circle: SET CUGF:<Status><geofence ID>-<alert type>-<shape>#<latitude-longitude (center point of circle)>#<radius in meter> Example for Polygon: SET CUGF:1-1777-3-1#10.0535097-76.334262#10.0504267-76.3328855#10.0474386-76.3439598#10.0503084-76.3437023#10.0535097-76.334262& Example for Circle: SET CUGF:1-1313-30#10.055625576.3544891#1000GET CUGF Response: NO of geofences: 1	Status 0 - Disable 1 - Enable Shape 0 - circle 1 - polygon Alert type 1-entry 2-exit 3-entry & exit	SET GET
FUELTYPE & FUELCFG	for TECHNO SET CUFUELTYPE:TECHNO485,1 Request Mode: SET CUFUELDATACFG:TECHNO,1,REQUEST,PERCENT,19200,01,20,01,PRE,POST,160,0,100,410 Passive Mode: SET CUFUELDATACFG:TECHNO,1,PUSH_HEX,PERCENT,19200,01,20,01,PRE,POST,160,0,100,410 for ESCORT, SET CUFUELTYPE:ESCORT485,1 Request Mode: SET CUFUELDATACFG:ESCORT,01,04,PERIODIC1023,SMART,SMART_0,15 Passive Mode: SET CUFUELDATACFG:ESCORT,01,04,PASSIVE1023,SMART,SMART_0,15 SET CUFUELMODE:1,1,15 FOR ITALON SET CUFUELTYPE:OMNICOM485,1 MASTER CONFIGURATIONS SET CUFUELDATACFG:OMNICOM,1,MASTER_BINARY,19200,02,12,BINARY,1023 for slave mode: SET CUFUELDATACFG:OMNICOM,1,SLAVE,19200,02,12,BINARY,1023 FOR STRELLA SET CUFUELTYPE:STRELLA232,1 Request Mode: SET CUFUELDATACFG:STRELLA,1,REQUEST,01,20 Passive Mode: SET CUFUELDATACFG:STRELLA,1,PUSH_HEX,01,20 OR FOR EUROSENS SET CUFUELTYPE:EUROSENS485,1 SET CUFUELDATACFG:EUROSENS,01,01		SET GET
DEVI	GET CUDEVI Response: device info packet	Get complete hardware and firmware details from the device	GET
DEVCFG	GET CUDEVCFG Response: configuraton info packet	Get entire configuration from device	GET
IMOB	SET CUIMOB:<ON/OFF> GET CUIMOB Example: SET CUIMOB:OFF GETCUIMOB Response: IMOB:OFF	Enable/Disable Immobilizer feature	SET GET
SL	SET CUSL:<Limit> GET CUSL Example: SET CUSL:70 GET CUSL Response: SPEEDLIMIT: 70	Configure speed limit for alerts	SET GET
ACCELENABLE	SET CUACCELENABLE:<0/1> Example: SET CUACCELENABLE:1 GET CUACCELENABLE Response: ACCELERO_ENABLE_STATUS: 1	1 - Enable 0 - Disable	SET GET
ORIENTATION	SET CUORIENTATION:<orientation number> Example: SET CUORIENTATION:1 GET CUORIENTATION Response: 1	Device mounting orientation: Orientation Number Explanation: 1 - Horizontal, power cable towards the driver, Antenna sky facing 2 - Vertical , power cable downward, Antenna facing driver 3 - Horizontal, power cable to the right, Antenna sky facing 4 - Vertical , power cable to the right, Antenna facing driver	SET GET
TA	SET CUTA:40 GET CUTA Response: TILT ANGLE THRESHOLD: 40	Tilt alert threshold in degrees	SET GET
VN	SET CUVN:<Vehicle No> Example: SET CUVN:<XXXXXXX> GET CUVN Response: VEHICLE_REG_NUMBER: XXXXXXX	Set/Get vehicle number	SET GET
CH	SET CUCH	Clearing history logs from device memory.	SET
MR	SET CUMR:<Number>	Microcontroller Restart: 1. Network Modem Immediate Restart 2. Network Modem Normal Restart, NVM Write true 3. Supervisory Controller Restarts Network Module 4. Supervisory Controller Immediate Restart 5. Supervisory Controller Normal Restart, NVM Write true	SET
FWINFO	GET CUFWINFO Response: FWINFO: TSD4G_0_3.0.2 FWINFO: TSDRB_0_3.0.1 FWINFO: TSD4R_0_1.0.3	Get firmware version info for: - Network Modem - Bootloader - Supervisory Controller	GET
IMEI	GET CUIMEI Response: IMEI: 869137069984441	Get device IMEI number	GET
SPI	GET CUSPI Response: REMAINING PACKETS=1566	Shows number of unsent packets stored in memory	GET
LOC	GET CULOC Response: LOC:Fix:0,Lat:0.000000,Lon:0.0000000,...	Get latest GPS location from device	GET
SUPT	GET CUSUPT Response: DEVICE_UPTIME: X-days X-hrs X-mins X-sec	Command to get the time from which the device was switched on. Response format: DEVICE_UPTIME:<days>-<hours>-<minutes>-<seconds>	GET
ODOMODE	SET CUODOMODE:<1/0> GET CUODOMODE Response: CUODOMODE:1	Set odometer calculation mode: 0 - Differential 1 - Accumulated	SET GET
ODO	SET ODO:<Number> Example: SET CUODO:111 GET CUODO Response: CUODO:111 METERS	Get/Set current odometer readings	SET GET
NWI (Network Info)	GET CUNWI Response: CUNWI:VI-404-19-1-1-20-0-0	Command to get the network information Response Format: CUNWI:<Operator Name>-<MCC>-<MNC>-<GSM nw reg stat>-<GPRS nw reg stat>-<signal strength>-<GSM nw reg loss tmr>-<GPRS nw reg loss timer> GSM network registered status : 1 – Registration OK 2 - Searching 3 - Deny 5 – Registration OK Roaming 0 – Not registered GPRS network registered status 1 – Registration OK 2 - Searching 3 - Deny 5 – Registration OK Roaming 0 – Not registered Signal Strength: 1 -31 in ASW GSM network registered loss timer : Time is seconds elapsed after GSM network registration loss GPRS network registered loss timer : Time is seconds elapsed after GPRS network registration loss	GET
COMSTAT	GET CUCOMSTAT Response: COMSTAT:4-0	Get communication success/failure counts	GET
ENOW	SET CUENOW:ON/OFF GET CUENOW Response: ENOW:OFF	Enable/Disable 1-wire sensor port	SET GET
OWCFG	SET CUOWCFG:<Sensor name> GET CUOWCFG Example: SET CUOWCFG:DS18B20 GET CUOWCFG Response: DS18B20	Configure the 1-wire sensor models 1-BS18B20 2-AM2305	SET GET
OWNOS	SET CUOWNOS:<No's> Example: SET CUOWNOS:2 GET CUOWNOS Response: TEMPERATURE SENSOR NOS: 2	Number of 1-wire sensors connected	SET GET