Commands of Discovery 4G

Configuration Commands	Example	Description	Commnad Type (SET/GET)
URL	SET CUURL:TCP:<IP>:<PORT> SET CUURL:url (HTTP) Example: SET CUURL:http://livedata.transight.net:6000/data SET CUURL:TCP:15.235.9.66:50334 GET CUURL Response: URL:http://livedata.customert.net:6000/data URL:TCP:15.235.9.66:50334	To SET and GET server URL for customer and transight IPs in HTTP and TCP protocol. Data packets will send from device to the pointed IP address.	SET GET
UR(in seconds).	SET CUUR:<duration> GET CUUR Example: SET CUUR:30 GET CUUR Response: UR: 30	Update rate in motion, duration is in seconds Packets will be generating in this frequency.	SET, GET
URT(halt,in minute).	SET CUURT:<duration in mins> GET CUURT Example: SET CUURT:30 GET CUURT Response: CUURT: 30	Update rate in halt, duration is in minutes	SET, GET
URS(sleep, in minute).	SET CUURS:<duration> GET CUURS Example: SET CUURS:30 GET CUURS Response: CUURS: 30	Update rate in sleep, duration is in minutes	SET, GET
M1	SET CUM1:<+91xxxxxxxxxx> GET CUM1 Response: M1: +919656691846	This enables the customer to configure the device and setup alert recipients.	SET, GET
M2	SET CUM2:<+91xxxxxxxxxx> GET CUM2 Response: M2: +919656691846	Secondary mobile number for alerts	SET, GET
M3	SET CUM3:<+91xxxxxxxxxx> GET CUM3 Response: M3: +919656691846	Third mobile number for alerts	SET, GET
APN	SET CUAPN:M2MISAFEcom SET CUAPN:airtelgprs.com GET CUAPN Response: APN:M2MISAFE	Access Point Name (APN) for internet connectivity	SET, GET
FRNO	SET CUFRNO:<number> GET CUFRNO Example: SET CUFRNO:12 GET CUFRNO Response: FRNO:12	Frame number for data transfer	SET GET
FSMODE	SET CUFSMODE:<0/1> GET CUFSMODE Example: SET CUFSMODE:1 GET CUFSMODE Response: FSMODE:1	0 - FIFO, 1 - LIFO Controls memory read/write mode	SET GET
IOCFG	SET CUIOCFG:IO1-AN-GEN*IO2-DI-GEN*IO3-DO-IMB* GET CUIOCFG	Configure I/O pin mode: DI, DO, AN (input/output/analog)	SET GET
ENIP	SET CUENIP:0.1,1.0 GET CUENIP Response: ENIP:0.1,1.0	Enable IPs: TS-0 / CU-1 Format: TS.ENABLED, CU.ENABLED	SET GET
DO	SET CUDO:1.0,2.0 GET CUDO Response: DO 1:OFF/ON - DO 2:OFF/ON	Controls Digital Output pins	SET GET
VID	SET CUVID:TRANSI GET CUVID Response: VID: TRANSI	Set/Get vendor ID	SET GET
DI	GET CUDI Response: DI:000	Get digital input status	GET
AI	GET CUAI Response: AI:0-0-0	Get analog input voltage values	GET
GF	SET CUGF:<status>-<id>-<alert>-<shape>#<coords>#...& GET CUGF Response: Number of geofences: X	Configure polygon/circle geofences Alert: 1-entry, 2-exit, 3-both	SET GET
FUELTYPE	SET CUFUELTYPE:<Fuel sensor name>,<No of sensors> Example: SET CUFUELTYPE:ESCORT485,1 Response: CUFUELNOS: 1 GET CUFUELTYPE Response: ESCORT485,1"	Sets type and number of fuel sensors	SET GET
FUELDATACFG	SET CUFUELDATACFG:<Fuel sensor configurations> SET CUFUELDATACFG:ESCORT,1,00,PASSIVE1023,SMART,SMART_0 GET CUFUELDATACFG:<Sensor name>,<Fuel sensor index> GET CUFUELDATACFG:ESCORT,1 Response: Mode: PERIODIC1023 Address: 0 Filter Type: SMART Filter: SMART_0 Interval: 0"	Configures fuel sensors: Number of Parameters may vary according to the sensor type. ESCORT485: Input parameters: Param1:ESCORT Param2:Network Address - 0x00 - 0xe7 Param3:Mode - PASSIVE1023 FREQUENCY1023 PERIODIC1023 PASSIVE4095 FREQUENCY4095 PERIODIC4095 Param4:Filtertype: SMART MEDIAN Param5:Filter: SMART_0 SMART_UPTO_200 SMART_200_1000 SMART_MORE_THAN_1000 SMART_HEAVY_CONDITIONS MEDIAN_0 to MEDIAN_9 Param6:Output intervel - In seconds (Not needed in request mode)	SET GET
	SET CUFUELDATACFG:TECHNO,1,PUSH_HEX,PERCENT,19200,01,15,01,PRE,POST,160,0,100,409 <TECHNO>,<Sensor index>,<Mode>,<Unit>,<Baurdrate>,<Network address>,<Output interval>,01,<Ascii pre extenstion>,<Ascii post extension>,<length of sensor>,<Min level>,<max level>,<Sensor firmware version>	TECHNOTON485 /232: Input parameters: Param1: TECHNO Param2: Sensor index - 0 to 3 Param3: Mode - REQUEST, PUSH_HEX, PUSH_ASCII,PUSH_ASCII_EXT, Param4:UnitMM,PERCENT,LITER,CUSTOM Param5: Baurdrate :19200 param6: Network address: 00 to FF Param7: Output interval:15 Param8: Autopushenable: 01 Param9&10: ASCII extensions for ASCII mode Param11: length of sensor, Param12&13: Min and Max level of sensor: 0 &100 param 14: Sensor firmware version number -409
	SET CUFUELDATACFG:STRELLA,1,REQUEST,01,15 <STRELLA>,<Sensor index>,<Mode>,<Network address>,<Output interval>
FUELMODE	SET CUFUELMODE:1,1,5 GET CUFUELMODE:1 Response: ESCORT485, Mode: PERIODIC	fuel sensor Mode: Param1:1-Request,0-Periodic Param2:Sensor Index Param3:Request Intervel in seconds	SET GET
FUELCALIBRATE	SET CUFUELCALIBRATE:FULL,1	Calibrate fuel level as FULL or EMPTY Specify sensor index	SET
DEVI	GET CUDEVI Response: JSON-formatted device info	Get complete hardware and firmware details from the device	GET
DEVCFG	GET CUDEVCFG Response: JSON-formatted config	Get entire configuration from device in JSON format	GET
IMOB	SET CUIMOB:ON GET CUIMOB Response: IMOB:OFF	Enable/Disable Immobilizer feature	SET GET
SL	SET CUSL:70 GET CUSL Response: SPEEDLIMIT: 70	Configure speed limit for alerts	SET GET
ACCELENABLE	SET CUACCELENABLE:1 GET CUACCELENABLE Response: ACCELERO_ENABLE_STATUS: 1	Enable/Disable accelerometer	SET GET
ORIENTATION	SET CUORIENTATION:1 GET CUORIENTATION Response: 1	Device mounting orientation: Orientation Number Explanation: 1 - Horizontal, power cable towards the driver, Antenna sky facing 2 - Vertical , power cable downward, Antenna facing driver 3 - Horizontal, power cable to the right, Antenna sky facing 4 - Vertical , power cable to the right, Antenna facing driver	SET GET
TA	SET CUTA:40 GET CUTA Response: TILT ANGLE THRESHOLD: 40	Tilt alert threshold in degrees	SET GET
VN	SET CUVN:TN51AN5503 GET CUVN Response: VEHICLE_REG_NUMBER: TN51AN5503	Set/Get vehicle number	SET GET
CH	SET CUCH	Clear command history/logs	SET
MR	SET CUMR:<Number>	Microcontroller Restart: 1. Network Modem Immediate Restart 2. Network Modem Normal Restart, NVM Write true 3. Supervisory Controller Restarts Network Module 4. Supervisory Controller Immediate Restart 5. Supervisory Conteoller Normal Restart, NVM Write true	SET
FWINFO	GET CUFWINFO Response: FWINFO: TSD4G_0_3.0.2 FWINFO: TSDRB_0_3.0.1 FWINFO: TSD4R_0_1.0.3	Get firmware version info for: - Network Modem - Bootloader - Supervisory Controller	GET
IMEI	GET CUIMEI Response: IMEI: 869137069984441	Get device IMEI number	GET
SPI	GET CUSPI Response: REMAINING PACKETS=1566	Shows number of unsent packets stored in memory	GET
LOC	GET CULOC Response: LOC:Fix:0,Lat:0.000000,Lon:0.0000000,...	Get latest GPS location from device	GET
SUPT	GET CUSUPT Response: DEVICE_UPTIME: X-days X-hrs X-mins X-sec	Get device uptime since last restart	GET
ODOMODE	SET CUODOMODE:1 GET CUODOMODE Response: CUODOMODE:1	Set odometer calculation mode: 0 - Differential 1 - Accumulated	SET GET
ODO	GET CUODO Response: CUODO:111 METERS	Get current odometer reading	GET
NWI	GET CUNWI Response: CUNWI:VI-404-19-1-1-17-0-0	Get network information: MCC, MNC, Signal, etc.	GET
COMSTAT	GET CUCOMSTAT Response: COMSTAT:4-0	Get communication success/failure counts	GET
ENOW	SET CUENOW:ON/OFF GET CUENOW Response: ENOW:OFF	Enable/Disable 1-wire sensor port	SET GET
OWCFG	SET CUOWCFG:DS18B20 GET CUOWCFG Response: DS18B20	Configure the 1-wire sensor model	SET GET
OWNOS	SET CUOWNOS:2 GET CUOWNOS Response: TEMPERATURE SENSOR NOS: 2	Number of 1-wire sensors connected	SET GET