Commands of Discovery 2G

Configuration Commands	Example and Response (CU)	Description	Command Type (SET/GET)
URL	SET CUURL:TCP:<IP>:<PORT> SET CUURL:url GET CUURL Response: URL:http://livedata.transight.net:6000/data URL:TCP:15.235.9.66:50334	To SET and GET server URL for customer and transight IPs in HTTP and TCP protocol. Data packets will be sent from the device to the configured IP address.	SET GET
UR (in seconds)	SET CUUR:<duration> GET CUUR Example: SET CUUR:30 GET CUUR Response: UR: 30	Update rate while in motion (in seconds). Determines packet sending frequency.	SET, GET
URT (halt, in minutes)	SET CUURT:<duration> GET CUURT Example: SET CUURT:30 GET CUURT Response: CUURT: 30	Update rate during halt (in minutes).	SET, GET
URS (sleep, in minutes)	SET CUURS:<duration> GET CUURS Example: SET CUURS:30 GET CUURS Response: CUURS: 30	Update rate during sleep (in minutes).	SET, GET
M1	SET CUM1:<+91xxxxxxxxxx> GET CUM1	Primary mobile number for alerts and configuration via SMS.	SET, GET
M2	SET CUM2:<+91xxxxxxxxxx> GET CUM2	Secondary mobile number.	SET, GET
APN	SET CUAPN:<APN> Example: SET CUAPN:airtelgprs.com GET CUAPN Response: APN:airtelgprs.com	Set Access Point Name (APN) based on SIM provider.	SET, GET
FRNO	SET CUFRNO:<number> GET CUFRNO Example: SET CUFRNO:12 Response: FRNO:12	Get or set frame number. Used for sequential frame control.	SET GET
FSMODE	SET CUFSMODE:<0/1> GET CUFSMODE Example: SET CUFSMODE:1 Response: FSMODE:1	File system mode: 0 = FIFO 1 = LIFO	SET GET
IOCFG	SET CUIOCFG:IO1-DI-GEN*IO2-DO-GEN*IO3-AN-GEN* Response: CUIOCFG:No ErrorDEQUEUE_SUCCESS GET CUIOCFG Response: NUM = 1 mode = DI fun = GEN NUM = 2 mode = DO fun = GEN NUM = 3 mode = AN fun = GEN CUIOCFG:IO1-DI-GEN*IO2-DO-GEN*IO3-AN-GEN	Configure pins as Digital Input, Output or Analog.	SET GET
ENIP	SET CUENIP:0.1,1.0 GET CUENIP Response: ENIP:0.1,1.0	SET TSENAPP:<IP>.<state>,<IP>.<state> IP:Transight-0, Customer-1 State:1- Enabled, 0- Disabled ENAPP:0.1,1.1	SET GET
DO	SET CUDO:1.n,2.n (n=0:off,1:on) GET CUDO Response: DO 1:OFF/ON - DO 2:OFF/ON	Digital output control for pins.	SET GET
VID	SET CUVID:TRANSI GET CUVID Response: VID: TRANS	Get/Set vendor ID.	SET GET
DI	GET CUDI Response: DI:000	Digital input status (LOW = 0, HIGH = 1)	GET
AI	GET CUAI Response: AI:0-0-0	Analog input voltage reading.	GET
ENOW	SET CUENOW:ON/OFF GET CUENOW Response: ENOW:OFF	Enable or disable 1-wire sensor.	SET GET
OWCFG	SET CUOWCFG:SET CUOWCFG:<name of sensor> Example: SET CUOWCFG:DS18B20 GET CUOWCFG	One-wire sensor configuration (e.g., DS18B20, AM2305)	SET GET
OWNOS	SET CUOWNOS:<Number of sensors> Example: GET CUOWNOS Response: TEMPERATURE SENSOR NOS: 2	Set or get number of 1-wire temperature sensors.	SET GET
GF (Geofence)	SET CUGF:<entry/delete>-<geofence ID>-<alert type>-<shape>#<latitude-longitude>#....& SET CUGF:<geofence ID>-<alert type>-<shape>#<latitude-longitude of center>#<radius in meter> Example for Polygon: SET CUGF:1-12345-1-1#10.0564051-76.3569957#10.0558456-76.3570601#10.0565529-76.3601607#10.0573870-76.3597316#10.0564051-76.356995& Example for Circle: SET CUGF:1-12345-1-0#10.0557866-76.3545692#5000()	Shape 0 - circle 1 - polygon Alert type 1-entry 2-exit 3-entry & exit	SET GET
FUELTYPE	SET CUFUELTYPE:ESCORT485,1 GET CUFUELTYPE Response: ESCORT485,1	Select fuel sensor type & number.	SET GET
FUELDATACFG	SET CUFUELDATACFG:ESCORT,1,00,PASSIVE1023,SMART,SMART_0 GET CUFUELDATACFG:ESCORT,1 Response: Filtered fuel data	Configure ESCORT485/TECHNO/OMNICOM/STRELLA/EUROSENS/INDIAN sensors.	SET GET
FUELMODE	SET CUFUELMODE:1,1,5 GET CUFUELMODE:1 Response: ESCORT485, Mode: PERIODIC	Fuel mode settings: 1 = Request 0 = Periodic Set sensor index & interval.	SET GET
FUELCALIBRATE	SET CUFUELCALIBRATE:FULL,1	Calibrate fuel level: FULL or EMPTY per sensor.	SET
DEVI	GET CUDEVI	Get complete device info in JSON format (raw packet).	GET
DEVCFG	GET CUDEVCFG	Get device configuration JSON packet.	GET
IMOB	SET CUIMOB:ON/OFF GET CUIMOB Response: IMOB:OFF	Enable or disable immobilizer feature.	SET GET
ORIENTATION	SET CUORIENTATION:1 GET CUORIENTATION Response: 1	Mounting orientation: 1 = Horizontal, Antenna up 2 = Vertical, Antenna forward, etc.	SET GET
ACCELENABLE	SET CUACCELENABLE:1 GET CUACCELENABLE Response: ACCELERO_ENABLE_STATUS: 1	Enable/Disable accelerometer.	SET GET
SL (Speed Limit)	SET CUSL:70 GET CUSL Response: SPEEDLIMIT: 70	Set maximum speed for alerts.	SET GET
HBT (Brake Threshold)	SET CUHBT:-4 GET CUHBT Response: BRAKE_THRESHOLD: -4.000000	Set harsh brake threshold in G-forces.	SET GET
HAT (Acceleration Threshold)	SET CUHAT:3 GET CUHAT Response: ACC_THRESHOLD: 3.000000	Set harsh acceleration threshold.	SET GET
RTT (Turn Threshold)	SET CURTT:3 GET CURTT Response: TURN_THRESHOLD: 3.000000	Set turn threshold in G-forces.	SET GET
TA (Tilt Angle)	SET CUTA:40 GET CUTA Response: TILT ANGLE THRESHOLD: 40	Set tilt alert threshold (degrees).	SET GET
VN (Vehicle Number)	SET CUVN:TN51AN5503 GET CUVN Response: VEHICLE_REG_NUMBER: TN51AN5503	Set or get registered vehicle number.	SET GET
CH (Clear History)	SET CUCH	Clear history logs from device.	SET
MR (Restart)	SET CUMR:<Number>	Restart Microcontroller Mode: 1. Immediate Restart 2. Normal Restart 3. Power Key restart 4. MCU immediate Restart 5. MCU Normal Restart	SET
FWINFO	GET CUFWINFO Response: FWINFO: TSD2G_0_3.0.2, etc.	Get firmware version info of all modules.	GET
IMEI	GET CUIMEI Response: IMEI: 869137069984441	Get device IMEI number.	GET
SPI	GET CUSPI Response: REMAINING PACKETS=1566	Get count of unsent packets in memory.	GET
LOC	GET CULOC Response: LAT/LON/SPEED/ALT/SAT	Get current location snapshot.	GET
SUPT (Uptime)	GET CUSUPT Response: DEVICE_UPTIME: d-h-m-s	Get device uptime since last reboot.	GET
ODOMODE	SET CUODOMODE:<0/1> GET CUODOMODE Response: CUODOMODE:1	Odometer mode: 1 = Accumulated 0 = Differential	SET GET
ODO	GET CUODO Response: CUODO:111 METERS	Get total odometer reading.	GET
NWI (Network Info)	GET CUNWI Response: CUNWI:VI-404-19-1-1-20-0-0	Command to get the network information Response Format: CUNWI:<Operator Name>-<MCC>-<MNC>-<GSM nw reg stat>-<GPRS nw reg stat>-<signal strength>-<GSM nw reg loss tmr>-<GPRS nw reg loss timer> GSM nw reg stat : 1 – Registration OK 2 - Searching 3 - Deny 5 – Registration OK Roaming 0 – Not registered GPRS nw reg stat 1 – Registration OK 2 - Searching 3 - Deny 5 – Registration OK Roaming 0 – Not registered Signal Strength: 1 -31 in ASW GSM nw reg loss timer : Time is seconds elapsed after GSM network registration loss GPRS nw reg loss timer : Time is seconds elapsed after GPRS network registration loss	GET
COMSTAT	GET CUCOMSTAT Response: COMSTAT:4-0	Get success/failure communication counts.	GET
SECURESMS	SET CUSECURESMS:<0/1> Example: SET CUSECURESMS:1 GET CUSECURESMS Response: SECURESMS:1	Enable or disable secure SMS feature.	SET GET