Jump to content

Commands of Discovery 2G

From Transight Wiki
Revision as of 05:00, 6 March 2026 by Editor (talk | contribs)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Configuration Commands Example and Response (CU) Description Command Type (SET/GET)
URL (SET SERVER) SET CUURL:TCP:<IP>:<PORT>
SET CUURL:url
GET CUURL
Response:
URL:http://livedata.transight.net:6000/data
URL:TCP:15.235.9.66:50334 		To SET and GET server URL for customer IP in HTTP and TCP protocol.
Data packets will be sent from the device to the configured IP address. 		SET GET
UR (in seconds) SET CUUR:<duration>
GET CUUR
Example:
SET CUUR:30
GET CUUR
Response: UR: 30 		Update rate while in motion (in seconds). Determines packet sending frequency. SET, GET
URT (halt, in minutes) SET CUURT:<duration>
GET CUURT
Example:
SET CUURT:30
GET CUURT
Response: CUURT: 30 		Update rate during halt (in minutes). SET, GET
URS (sleep, in minutes) SET CUURS:<duration>
GET CUURS
Example:
SET CUURS:30
GET CUURS
Response: CUURS: 30 		Update rate during sleep (in minutes). SET, GET
M1 SET CUM1:<+91xxxxxxxxxx>
GET CUM1 		Primary mobile number for alerts and configuration via SMS. SET, GET
M2 SET CUM2:<+91xxxxxxxxxx>
GET CUM2 		Secondary mobile number. SET, GET
APN SET CUAPN:<APN>
Example:
SET CUAPN:airtelgprs.com
GET CUAPN
Response: APN:airtelgprs.com 		Set Access Point Name (APN) based on SIM provider. SET, GET
FRNO SET CUFRNO:<number>
GET CUFRNO
Example: SET CUFRNO:12
Response: FRNO:12 		Get or set frame number. Used for sequential frame control. SET GET
FSMODE SET CUFSMODE:<0/1>
GET CUFSMODE
Example: SET CUFSMODE:1
Response: FSMODE:1 		File system mode:
0 = FIFO
1 = LIFO 		SET GET
IOCFG SET CUIOCFG:<IO Number>-<IO Mode>-<IO Function*>-<IO Number>-<IO Mode>-<IO Function*>-<IO Number><IO Mode>-<IO Function*>
Example:
SET CUIOCFG:IO1-DI-GEN*IO2-DO-GEN*IO3-AN-GEN*
GET CUIOCFG
Response
CUIOCFG:
IO1-DI-GEN*IO2-DO-GEN*IO3-AN-GEN 		This command is used to configure the pin as Digital Input, or Digital Output, or Analog.
AN - Analog
DO - Digital Output
DI - Digital Input 		SET GET
ENIP SET CUENIP:<IP>.<state>,<IP>.<state>
Example:
SET CUENIP:0.1,1.0
GET CUENIP
Response:
ENIP:0.1,1.0 		IP:Transight-0, Customer-1

State:
1- Enabled
0- Disabled
ENIP:0.1,1.1

SET GET
DO SET CUDO:1.n,2.n (n=0:off,1:on)
GET CUDO
Response: DO 1:OFF/ON - DO 2:OFF/ON 		Digital output control for pins. SET GET
VID SET CUVID:TRANSI
GET CUVID
Response: VID: TRANS 		Get/Set vendor ID. SET GET
DI GET CUDI
Response: DI:000 		Digital input status (LOW = 0, HIGH = 1) GET
AI GET CUAI
Response: AI:0-0-0 		Analog input voltage reading. GET
ENOW SET CUENOW:ON/OFF
GET CUENOW
Response: ENOW:OFF 		Enable or disable 1-wire sensor. SET GET
OWCFG SET CUOWCFG:<name of sensor>
GET CUOWCFG
Example:
SET CUOWCFG:DS18B20
GET CUOWCFG 		One-wire sensor configuration (e.g., DS18B20, AM2305) SET GET
OWNOS SET CUOWNOS:<Number of sensors>
Example:
GET CUOWNOS
Response: TEMPERATURE SENSOR NOS: 2 		Set or get number of 1-wire temperature sensors. SET GET
GF (Geofence) SET CUGF:<entry/delete>-<geofence ID>-<alert type>-<shape>#<latitude-longitude>#....&

SET CUGF:<geofence ID>-<alert type>-<shape>#<latitude-longitude of center>#<radius in meter>
Example for Polygon:
SET CUGF:1-12345-1-1#10.0564051-76.3569957#10.0558456-76.3570601#10.0565529-76.3601607#10.0573870-76.3597316#10.0564051-76.356995&
Example for Circle:
SET CUGF:1-12345-1-0#10.0557866-76.3545692#5000()

 Shape
0 - circle
1 - polygon
Alert type
1-entry
2-exit
3-entry & exit 		SET GET
FUELTYPE SET CUFUELTYPE:<Fuel sensor name>,<No of sensors>

Example:
SET CUFUELTYPE:ESCORT485,1
Response:
CUFUELNOS: 1
GET CUFUELTYPE
Response:
ESCORT485,1

Enables and Selects fuel sensor Type:

Param1:
TECHNO485,OMNICOM485,ESCORT485,OFF
Param2:
Number of fuel sensors attached

SET GET
DEVI GET CUDEVI Get complete device info packet. GET
DEVCFG GET CUDEVCFG Get device configuration info packet. GET
IMOB SET CUIMOB:<ON/OFF>
GET CUIMOB
Example:
SET CUIMOB:OFF
GETCUIMOB
Response:
IMOB:OFF 		Enable/Disable Immobilizer feature SET GET
ORIENTATION SET CUORIENTATION:<orientation number>
Example:

SET CUORIENTATION:1
GET CUORIENTATION
Response:
1

Device mounting orientation:
Orientation Number Explanation:

1 - Horizontal, power cable towards the driver, Antenna sky facing
2 - Vertical , power cable downward, Antenna facing driver
3 - Horizontal, power cable to the right, Antenna sky facing
4 - Vertical , power cable to the right, Antenna facing driver

 SET GET
ACCELENABLE SET CUACCELENABLE:<0/1>
Example:
SET CUACCELENABLE:1
GET CUACCELENABLE
Response:
ACCELERO_ENABLE_STATUS: 1 		1 - Enable
0 - Disable 		SET GET
SL SET CUSL:<Limit>
GET CUSL
Example:
SET CUSL:70
GET CUSL
Response:
SPEEDLIMIT: 70 		Configure speed limit for alerts SET GET
HBT (Brake Threshold) SET CUHBT:-4
GET CUHBT
Response: BRAKE_THRESHOLD: -4.000000 		Set harsh brake threshold in G-forces. SET GET
HAT (Acceleration Threshold) SET CUHAT:3
GET CUHAT
Response: ACC_THRESHOLD: 3.000000 		Set harsh acceleration threshold. SET GET
RTT (Turn Threshold) SET CURTT:3
GET CURTT
Response: TURN_THRESHOLD: 3.000000 		Set turn threshold in G-forces. SET GET
TA (Tilt Angle) SET CUTA:40
GET CUTA
Response: TILT ANGLE THRESHOLD: 40 		Set tilt alert threshold (degrees). SET GET
VN (Vehicle Number) SET CUVN:<Vehicle No>
Example:
SET CUVN:<XXXXXXX>
GET CUVN
Response:
VEHICLE_REG_NUMBER: XXXXXXX 		Set/Get vehicle number SET GET
CH (Clear History) SET CUCH Clear history logs from device. SET
MR SET CUMR:<Number> Microcontroller Restart:

1. Network Modem Immediate Restart
2. Network Modem Normal Restart, NVM Write true
3. Supervisory Controller Restarts Network Module
4. Supervisory Controller Immediate Restart
5. Supervisory Controller Normal Restart, NVM Write true

 SET
FWINFO GET CUFWINFO
Response:
FWINFO: TSD4G_0_3.0.2
FWINFO: TSDRB_0_3.0.1
FWINFO: TSD4R_0_1.0.3 		Get firmware version info for:
- Network Modem
- Bootloader
- Supervisory Controller 		GET
IMEI GET CUIMEI
Response: IMEI: 869137069984441 		Get device IMEI number. GET
SPI GET CUSPI
Response: REMAINING PACKETS=1566 		Get count of unsent packets in memory. GET
LOC GET CULOC
Response: LAT/LON/SPEED/ALT/SAT 		Get current location snapshot. GET
SUPT (Uptime) GET CUSUPT
Response: DEVICE_UPTIME: d-h-m-s 		Get device uptime since last reboot. GET
ODOMODE SET CUODOMODE:<0/1>
GET CUODOMODE
Response: CUODOMODE:1 		Odometer mode:
1 = Accumulated
0 = Differential 		SET GET
ODO SET ODO:<Number>
Example:
SET CUODO:111
GET CUODO
Response:
CUODO:111 METERS 		Get/Set current odometer readings SET GET
NWI (Network Info) GET CUNWI
Response:
CUNWI:VI-404-19-1-1-20-0-0 		Command to get the network information

Response Format: CUNWI:<Operator Name>-<MCC>-<MNC>-<GSM nw reg stat>-<GPRS nw reg stat>-<signal strength>-<GSM nw reg loss tmr>-<GPRS nw reg loss timer> GSM nw reg stat :

1 – Registration OK
2 - Searching
3 - Deny
5 – Registration OK Roaming
0 – Not registered

GPRS nw reg stat 

1 – Registration OK
2 - Searching
3 - Deny
5 – Registration OK Roaming
0 – Not registered

Signal Strength: 1 -31 in ASW
GSM nw reg loss timer : Time is seconds elapsed after GSM network registration loss
GPRS nw reg loss timer : Time is seconds elapsed after GPRS network registration loss

GET
COMSTAT GET CUCOMSTAT
Response: COMSTAT:4-0 		Get success/failure communication counts. GET
SECURESMS SET CUSECURESMS:<0/1>
Example:
SET CUSECURESMS:1
GET CUSECURESMS
Response: SECURESMS:1 		Enable or disable secure SMS feature. SET GET
Retrieved from "https://telematics.transight.com/index.php?title=Commands_of_Discovery_2G&oldid=1440"