Commands of Discovery 4G
| Configuration Commands | Example | Description | Commnad Type (SET/GET) |
|---|---|---|---|
| URL | SET CUURL:TCP:<IP>:<PORT> SET CUURL:url (HTTP) Example: SET CUURL:http://livedata.transight.net:6000/data SET CUURL:TCP:15.235.9.66:50334 GET CUURL Response: URL:http://livedata.customert.net:6000/data URL:TCP:15.235.9.66:50334 |
To SET and GET server URL for customer and transight IPs in HTTP and TCP protocol. Data packets will send from device to the pointed IP address. |
SET GET |
| UR(in seconds). | SET CUUR:<duration> GET CUUR Example: SET CUUR:30 GET CUUR Response: UR: 30 |
Update rate in motion, duration is in seconds Packets will be generating in this frequency. |
SET, GET |
| URT(halt,in minute). | SET CUURT:<duration in mins> GET CUURT Example: SET CUURT:30 GET CUURT Response: CUURT: 30 |
Update rate in halt, duration is in minutes | SET, GET |
| URS(sleep, in minute). | SET CUURS:<duration> GET CUURS Example: SET CUURS:30 GET CUURS Response: CUURS: 30 |
Update rate in sleep, duration is in minutes | SET, GET |
| M1 | SET CUM1:<+91xxxxxxxxxx> GET CUM1 Response: M1: +919656691846 |
This enables the customer to configure the device and setup alert recipients. | SET, GET |
| M2 | SET CUM2:<+91xxxxxxxxxx> GET CUM2 Response: M2: +919656691846 |
Secondary mobile number for alerts | SET, GET |
| M3 | SET CUM3:<+91xxxxxxxxxx> GET CUM3 Response: M3: +919656691846 |
Third mobile number for alerts | SET, GET |
| APN | SET CUAPN:M2MISAFEcom SET CUAPN:airtelgprs.com GET CUAPN Response: APN:M2MISAFE |
Access Point Name (APN) for internet connectivity | SET, GET |
| FRNO | SET CUFRNO:<number> GET CUFRNO Example: SET CUFRNO:12 GET CUFRNO Response: FRNO:12 |
Frame number for data transfer | SET GET |
| FSMODE | SET CUFSMODE:<0/1> GET CUFSMODE Example: SET CUFSMODE:1 GET CUFSMODE Response: FSMODE:1 |
0 - FIFO, 1 - LIFO Controls memory read/write mode |
SET GET |
| IOCFG | SET CUIOCFG:IO1-AN-GEN*IO2-DI-GEN*IO3-DO-IMB* GET CUIOCFG |
Configure I/O pin mode: DI, DO, AN (input/output/analog) | SET GET |
| ENIP | SET CUENIP:0.1,1.0 GET CUENIP Response: ENIP:0.1,1.0 |
Enable IPs: TS-0 / CU-1 Format: TS.ENABLED, CU.ENABLED |
SET GET |
| DO | SET CUDO:1.0,2.0 GET CUDO Response: DO 1:OFF/ON - DO 2:OFF/ON |
Controls Digital Output pins | SET GET |
| VID | SET CUVID:TRANSI GET CUVID Response: VID: TRANSI |
Set/Get vendor ID | SET GET |
| DI | GET CUDI Response: DI:000 |
Get digital input status | GET |
| AI | GET CUAI Response: AI:0-0-0 |
Get analog input voltage values | GET |
| GF | SET CUGF:<status>-<id>-<alert>-<shape>#<coords>#...& GET CUGF Response: Number of geofences: X |
Configure polygon/circle geofences Alert: 1-entry, 2-exit, 3-both |
SET GET |
| FUELTYPE | SET CUFUELTYPE:ESCORT485,1 GET CUFUELTYPE Response: ESCORT485,1 |
Sets type and number of fuel sensors | SET GET |
| FUELDATACFG | SET CUFUELDATACFG:ESCORT,1,00,PASSIVE1023,SMART,SMART_0 GET CUFUELDATACFG:ESCORT,1 |
Configure fuel sensor parameters based on type | SET GET |
| FUELMODE | SET CUFUELMODE:1,1,5 GET CUFUELMODE:1 Response: ESCORT485, Mode: PERIODIC |
Fuel sensor Mode: 1-Request 0-Periodic Includes request interval in seconds |
SET GET |
| FUELCALIBRATE | SET CUFUELCALIBRATE:FULL,1 | Calibrate fuel level as FULL or EMPTY Specify sensor index |
SET |
| DEVI | GET CUDEVI Response: JSON-formatted device info |
Get complete hardware and firmware details from the device | GET |
| DEVCFG | GET CUDEVCFG Response: JSON-formatted config |
Get entire configuration from device in JSON format | GET |
| IMOB | SET CUIMOB:ON GET CUIMOB Response: IMOB:OFF |
Enable/Disable Immobilizer feature | SET GET |
| FOTAURL | GET CUFOTAURL Response: FOTA details |
Used to get/set FOTA URL and firmware config | SET GET |
| SL | SET CUSL:70 GET CUSL Response: SPEEDLIMIT: 70 |
Configure speed limit for alerts | SET GET |
| ACCELENABLE | SET CUACCELENABLE:1 GET CUACCELENABLE Response: ACCELERO_ENABLE_STATUS: 1 |
Enable/Disable accelerometer | SET GET |
| TA | SET CUTA:40 GET CUTA Response: TILT ANGLE THRESHOLD: 40 |
Tilt alert threshold in degrees | SET GET |
| VN | SET CUVN:TN51AN5503 GET CUVN Response: VEHICLE_REG_NUMBER: TN51AN5503 |
Set/Get vehicle number | SET GET |
| CH | SET CUCH | Clear command history/logs | SET |
| MR | SET CUMR:<Number> | Microcontroller Restart: 1. Network Modem Immediate Restart |
SET |
| FWINFO | GET CUFWINFO Response: FWINFO: TSD4G_0_3.0.2 FWINFO: TSDRB_0_3.0.1 FWINFO: TSD4R_0_1.0.3 |
Get firmware version info for: - Network Modem - Bootloader - Supervisory Controller |
GET |
| IMEI | GET CUIMEI Response: IMEI: 869137069984441 |
Get device IMEI number | GET |
| SPI | GET CUSPI Response: REMAINING PACKETS=1566 |
Shows number of unsent packets stored in memory | GET |
| LOC | GET CULOC Response: LOC:Fix:0,Lat:0.000000,Lon:0.0000000,... |
Get latest GPS location from device | GET |
| SUPT | GET CUSUPT Response: DEVICE_UPTIME: X-days X-hrs X-mins X-sec |
Get device uptime since last restart | GET |
| ODOMODE | SET CUODOMODE:1 GET CUODOMODE Response: CUODOMODE:1 |
Set odometer calculation mode: 0 - Differential 1 - Accumulated |
SET GET |
| ODO | GET CUODO Response: CUODO:111 METERS |
Get current odometer reading | GET |
| NWI | GET CUNWI Response: CUNWI:VI-404-19-1-1-17-0-0 |
Get network information: MCC, MNC, Signal, etc. |
GET |
| COMSTAT | GET CUCOMSTAT Response: COMSTAT:4-0 |
Get communication success/failure counts | GET |
| ENOW | SET CUENOW:ON/OFF GET CUENOW Response: ENOW:OFF |
Enable/Disable 1-wire sensor port | SET GET |
| OWCFG | SET CUOWCFG:DS18B20 GET CUOWCFG Response: DS18B20 |
Configure the 1-wire sensor model | SET GET |
| OWNOS | SET CUOWNOS:2 GET CUOWNOS Response: TEMPERATURE SENSOR NOS: 2 |
Number of 1-wire sensors connected | SET GET |
| ORIENTATION | SET CUORIENTATION:1 GET CUORIENTATION Response: 1 |
Device mounting orientation: Orientation Number Explanation: 1 - Horizontal, power cable towards the driver, Antenna sky facing |
SET GET |