Jump to content

Commands of Discovery 4G

From Transight Wiki
Revision as of 10:34, 7 August 2025 by Editor (talk | contribs)
Configuration Commands Example Description Commnad Type (SET/GET)
URL SET CUURL:TCP:<IP>:<PORT>
SET CUURL:url (HTTP)

Example:
SET CUURL:http://livedata.transight.net:6000/data
SET CUURL:TCP:15.235.9.66:50334
GET CUURL
Response:
URL:http://livedata.customert.net:6000/data
URL:TCP:15.235.9.66:50334 		To SET and GET server URL for customer and transight IPs in HTTP and TCP protocol.
Data packets will send from device to the pointed IP address. 		SET GET
UR(in seconds). SET CUUR:<duration>
GET CUUR
Example:
SET CUUR:30
GET CUUR
Response:
UR: 30 		Update rate in motion, duration is in seconds
Packets will be generating in this frequency. 		SET, GET
URT(halt,in minute). SET CUURT:<duration in mins>
GET CUURT
Example:
SET CUURT:30
GET CUURT
Response:
CUURT: 30 		Update rate in halt, duration is in minutes SET, GET
URS(sleep, in minute). SET CUURS:<duration>
GET CUURS
Example:
SET CUURS:30
GET CUURS
Response:
CUURS: 30 		Update rate in sleep, duration is in minutes SET, GET
M1 SET CUM1:<+91xxxxxxxxxx>
GET CUM1
Response:
M1: +919656691846 		This enables the customer to configure the device and setup alert recipients. SET, GET
M2 SET CUM2:<+91xxxxxxxxxx>
GET CUM2
Response:
M2: +919656691846 		Secondary mobile number for alerts SET, GET
M3 SET CUM3:<+91xxxxxxxxxx>
GET CUM3
Response:
M3: +919656691846 		Third mobile number for alerts SET, GET
APN SET CUAPN:M2MISAFEcom
SET CUAPN:airtelgprs.com
GET CUAPN
Response:
APN:M2MISAFE 		Access Point Name (APN) for internet connectivity SET, GET
FRNO SET CUFRNO:<number>
GET CUFRNO
Example:
SET CUFRNO:12
GET CUFRNO
Response:
FRNO:12 		Frame number for data transfer SET GET
FSMODE SET CUFSMODE:<0/1>
GET CUFSMODE
Example:
SET CUFSMODE:1
GET CUFSMODE
Response:
FSMODE:1 		0 - FIFO, 1 - LIFO
Controls memory read/write mode 		SET GET
IOCFG SET CUIOCFG:IO1-AN-GEN*IO2-DI-GEN*IO3-DO-IMB*
GET CUIOCFG 		Configure I/O pin mode: DI, DO, AN (input/output/analog) SET GET
ENIP SET CUENIP:0.1,1.0
GET CUENIP
Response:
ENIP:0.1,1.0 		Enable IPs: TS-0 / CU-1
Format: TS.ENABLED, CU.ENABLED 		SET GET
DO SET CUDO:1.0,2.0
GET CUDO
Response:
DO 1:OFF/ON - DO 2:OFF/ON 		Controls Digital Output pins SET GET
VID SET CUVID:TRANSI
GET CUVID
Response:
VID: TRANSI 		Set/Get vendor ID SET GET
DI GET CUDI
Response:
DI:000 		Get digital input status GET
AI GET CUAI
Response:
AI:0-0-0 		Get analog input voltage values GET
GF SET CUGF:<status>-<id>-<alert>-<shape>#<coords>#...&
GET CUGF
Response:
Number of geofences: X 		Configure polygon/circle geofences
Alert: 1-entry, 2-exit, 3-both 		SET GET
FUELTYPE SET CUFUELTYPE:<Fuel sensor name>,<No of sensors>

Example:
SET CUFUELTYPE:ESCORT485,1
Response:
CUFUELNOS: 1
GET CUFUELTYPE Response: ESCORT485,1"

Sets type and number of fuel sensors SET GET
FUELDATACFG SET CUFUELDATACFG:<Fuel sensor configurations>

SET CUFUELDATACFG:ESCORT,1,00,PASSIVE1023,SMART,SMART_0
GET CUFUELDATACFG:<Sensor name>,<Fuel sensor index>
GET CUFUELDATACFG:ESCORT,1
Response:
Mode: PERIODIC1023
Address: 0
Filter Type: SMART
Filter: SMART_0
Interval: 0"

 Configures fuel sensors:

Number of Parameters may vary according to the sensor type.
ESCORT485:
Input parameters:
Param1:ESCORT
Param2:Network Address - 0x00 - 0xe7
Param3:Mode - PASSIVE1023 FREQUENCY1023 PERIODIC1023 PASSIVE4095 FREQUENCY4095 PERIODIC4095 Param4:Filtertype: SMART MEDIAN Param5:Filter: SMART_0 SMART_UPTO_200 SMART_200_1000 SMART_MORE_THAN_1000 SMART_HEAVY_CONDITIONS MEDIAN_0 to MEDIAN_9 Param6:Output intervel - In seconds (Not needed in request mode)

SET GET SET CUFUELDATACFG:TECHNO,1,PUSH_HEX,PERCENT,19200,01,15,01,PRE,POST,160,0,100,409 <TECHNO>,<Sensor index>,<Mode>,<Unit>,<Baurdrate>,<Network address>,<Output interval>,01,<Ascii pre extenstion>,<Ascii post extension>,<length of sensor>,<Min level>,<max level>,<Sensor firmware version> "TECHNOTON485 /232:

Input parameters: Param1:TECHNO Param2:Sensor index - 0 to 3 Param3:Mode - REQUEST, PUSH_HEX, PUSH_ASCII,PUSH_ASCII_EXT, Param4:Unit - MM, PERCENT, LITER,CUSTOM Param5:Baurdrate :19200 param6:Network address: 00 to FF Param7:Output interval:15 Param8:Autopushenable: 01 Param9&10: ASCII extensions for ASCII mode Param11: length of sensor, Param12&13: Min and Max level of sensor: 0 &100 param 14: Sensor firmware version number -409"

SET CUFUELDATACFG:STRELLA,1,REQUEST,01,15 <STRELLA>,<Sensor index>,<Mode>,<Network address>,<Output interval>
FUELMODE SET CUFUELMODE:1,1,5
GET CUFUELMODE:1
Response:
ESCORT485, Mode: PERIODIC 		Fuel sensor Mode:
1-Request
0-Periodic
Includes request interval in seconds 		SET GET
FUELCALIBRATE SET CUFUELCALIBRATE:FULL,1 Calibrate fuel level as FULL or EMPTY
Specify sensor index 		SET
DEVI GET CUDEVI
Response: JSON-formatted device info 		Get complete hardware and firmware details from the device GET
DEVCFG GET CUDEVCFG
Response: JSON-formatted config 		Get entire configuration from device in JSON format GET
IMOB SET CUIMOB:ON
GET CUIMOB
Response:
IMOB:OFF 		Enable/Disable Immobilizer feature SET GET
SL SET CUSL:70
GET CUSL
Response:
SPEEDLIMIT: 70 		Configure speed limit for alerts SET GET
ACCELENABLE SET CUACCELENABLE:1
GET CUACCELENABLE
Response:
ACCELERO_ENABLE_STATUS: 1 		Enable/Disable accelerometer SET GET
ORIENTATION SET CUORIENTATION:1
GET CUORIENTATION
Response:
1 		Device mounting orientation:
Orientation Number Explanation:

1 - Horizontal, power cable towards the driver, Antenna sky facing
2 - Vertical , power cable downward, Antenna facing driver
3 - Horizontal, power cable to the right, Antenna sky facing
4 - Vertical , power cable to the right, Antenna facing driver

 SET GET
TA SET CUTA:40
GET CUTA
Response:
TILT ANGLE THRESHOLD: 40 		Tilt alert threshold in degrees SET GET
VN SET CUVN:TN51AN5503
GET CUVN
Response:
VEHICLE_REG_NUMBER: TN51AN5503 		Set/Get vehicle number SET GET
CH SET CUCH Clear command history/logs SET
MR SET CUMR:<Number> Microcontroller Restart:

1. Network Modem Immediate Restart
2. Network Modem Normal Restart, NVM Write true
3. Supervisory Controller Restarts Network Module
4. Supervisory Controller Immediate Restart
5. Supervisory Conteoller Normal Restart, NVM Write true

 SET
FWINFO GET CUFWINFO
Response:
FWINFO: TSD4G_0_3.0.2
FWINFO: TSDRB_0_3.0.1
FWINFO: TSD4R_0_1.0.3 		Get firmware version info for:
- Network Modem
- Bootloader
- Supervisory Controller 		GET
IMEI GET CUIMEI
Response:
IMEI: 869137069984441 		Get device IMEI number GET
SPI GET CUSPI
Response:
REMAINING PACKETS=1566 		Shows number of unsent packets stored in memory GET
LOC GET CULOC
Response:
LOC:Fix:0,Lat:0.000000,Lon:0.0000000,... 		Get latest GPS location from device GET
SUPT GET CUSUPT
Response:
DEVICE_UPTIME: X-days X-hrs X-mins X-sec 		Get device uptime since last restart GET
ODOMODE SET CUODOMODE:1
GET CUODOMODE
Response:
CUODOMODE:1 		Set odometer calculation mode:
0 - Differential
1 - Accumulated 		SET GET
ODO GET CUODO
Response:
CUODO:111 METERS 		Get current odometer reading GET
NWI GET CUNWI
Response:
CUNWI:VI-404-19-1-1-17-0-0 		Get network information:
MCC, MNC, Signal, etc. 		GET
COMSTAT GET CUCOMSTAT
Response:
COMSTAT:4-0 		Get communication success/failure counts GET
ENOW SET CUENOW:ON/OFF
GET CUENOW
Response:
ENOW:OFF 		Enable/Disable 1-wire sensor port SET GET
OWCFG SET CUOWCFG:DS18B20
GET CUOWCFG
Response:
DS18B20 		Configure the 1-wire sensor model SET GET
OWNOS SET CUOWNOS:2
GET CUOWNOS
Response:
TEMPERATURE SENSOR NOS: 2 		Number of 1-wire sensors connected SET GET
Retrieved from "https://telematics.transight.com/index.php?title=Commands_of_Discovery_4G&oldid=915"